Page 13 - catalogo Tillett

TB FIA race seat bracket
Beautiful and strong the Tillett TB FIA brackets point
outwards and combine gorgeous looks with
ultra-strong performance. They are machined from
solid aluminium billet and are without doubt the
ultimate car seat brackets.
Available in natural lacquered aluminium or
anodised black.
TB FIA bracket sets include special pegged
aluminium spacers for use supporting the
adjustment slots for even more strength. 1.3 kg
Lotus Elise Exige specific EB range of brackets.
EB F2 The EBF2 bracket is designed to solidly
fit the B6/B7 shaped seats to the driver’s seat of
the Elise/Exige for race and track applications.
Designed as a replacement for the EBF1 bracket, t,
the new EBF2 is machined from billet
aluminium, they are super light and look
amazing with their clear lacquer finish. They
allow adjustment of angle, height and leg length. .
The standard width B6/B7 shaped seats will fit in n
the passenger side with the EBF2 but not the
B6-43 XL Screamer. For the XL 43 Screamer seat
at
in the passenger side use the EB4. Unlike the
EB4, the EBF2 does not include hip belt mounting
points and requires the seat belt hard points to
be independent of these brackets.
The EBF2 bracket set comes complete with a
special fixings and spacer kit. 0.7 kg
EB4 This steel EB4 bracket set is designed to fit
the side mounted B6 Screamer/B7 seats in the
Elise/Exige. With careful setup these allow the
seat to fit in either driver or passenger side of
both left and right hand drive cars. It can also be
used to fit the wide Screamer XL 43 into the car.
They allow adjustment of angle, height and leg
length in 5 mm increments. The length of leg is
adjusted by means of a U channel and the
position can be set every 5 mm. The EB4
incorporates hip belt mounting points and a
strengthened U channel to cope with the extra
load. 2.2 kg
EB5 This 3 mm steel Elise/Exige specific bracket
set is made for fitting either a B6 Screamer, B7,
or B6-43 XL Screamer seat to the original Lotus
runners. They allow the driver to adjust the angle
and height of the seat. They also have mounting
points for the original seat belt mountings.
1 kg
www.tillett.co.uk
Elise/Exige specifically for the B5 seat
EB1 side mounted seat brackets for fitting the B5 to
the Elise/Exige.
The EB1 is useable in both RHD/LHD cars for both
mm
driver and passenger sides. This strong and rigid 3 mm
thick steel mounting bracket set is designed to solidly ly
fit a B5 seat to the Elise/Exige for race and track
ht
applications and it allows adjustment of angle, height
g is
and leg length in 5 mm increments. The length of leg is
adjusted by means of a U channel and the position can
an
be set every 5 mm. The EB1 incorporates seat belt ope
mounting points and a strengthened U channel to cope
with the extra load. 2.2 kg
EB2 This 3 mm thick steel mounting bracket set is
designed to fit directly on top of the existing
Elise/Exige runners and allows the driver to adjust
the angle and height of the B5 seat. They also have
mounting points for the original seat belt mountings.
1 kg
Generic brackets specifically for the B5 seat
TB2 side mounted brackets suit the B5 car seat in
road, race and track applications. These are made
from 5 mm thick aluminium and allow the seats to
be tipped, raised and lowered. TB2 brackets are 90°
and therefore can point inwards or outwards. They
can be used with TR1 seat adjustment runners for
road use and are useful with a dropped floor pan
which is lower than the mounting area. 1.1 kg
TB3 side mounted brackets are a 30 mm taller
version of the TB2. It is sometimes necessary to lift
the seat in a saloon car as the B5 driving position is
very low when compared to regular seats. TB3
brackets are 90° and therefore can point inwards or
outwards. 1.36 kg
Seat Adjustment Runners
TR1 adjustable seat runner sets are made to be
used in conjunction with the lower holes on our car
seat brackets. They also fit directly to the bottom of
the W2, W3 and W4 seats when fitted with the
optional backframe moulding. The runners also fit to
the bottom of the standard B6 seat and the W1i with
backframe using the additional TK5 spacer kit. They
have a hole to hole spacing of 31.5 cm square.
1.38 kg
It is not recommended to use any seat
TR2 Identical to the TR1 with the handle 90 mm adjustment runners for racing purposes,
wider to accommodate being fitted to the bottom of as they are only intended for road use.
TB5, TBF5, TBFIA brackets and TB2 and TB3 when
they are used pointing outwards. 1.38 kg Due to constant product developments all
weights quoted in the brochure are
approximate.