Page 106 - Catalogo Bell 2024
P. 106
ai1703684047244_BRE 2024 96 97 ok Print.pdf 1 27/12/2023 4:34 PM
CUSTOM PAINTING
SERVICE
1. POSITIONING THE HELMET ON YOUR HEAD
Put the helmet on by grasping the chin strap halves in each hand and pull the helmet on over your head.
HOW TO FIT A HELMET
FACTORY CUSTOM PAINTING SERVICE
Bell Racing offers factory custom painting with the guarantee that the painting will not affect the original protective qualities of the helmet. 1. POSITIONING THE HELMET ON YOUR HEAD
Each painted helmet comes with an official certificate, proving its conformity with the FIA safety regulations. Put the helmet on by grasping the chin strap halves in each hand and pull the helmet on over your head.
Our experience over the past years in painting the helmets of F1 and other professional drivers enables us to reproduce almost every possible
design and colours.
2. FITTING THE HELMET
When properly positioned, the helmet should be worn low on the brow eyes, near the
center of the eye opening, touching the top of the head with uniform and firm pressure
all around – tight without excessive pressure points.
PAINTING JOB LEVEL 1 2170031
To fasten the chin strap, thread the end of the strap through both d-rings, loop the strap
PAINTING JOB LEVEL 2 2170032 end back through the inner d-ring and pull it comfortably tight against the throat. Make
sure the chin strap is snug against the throat.
PAINTING JOB LEVEL 3 2170033
PAINTING JOB LEVEL 4 2170034
WARNING CORRECTLY USING THE CHIN STRAP
GRAPHICS DEVELOPMENT DESIGN ONE VIEW 2170011 A good fit and a properly fastened chin strap are all that keep the helmet on your head
during an accident. Make sure the chin strap is correctly fastened and pulled snugly up
GRAPHICS DEVELOPMENT DESIGN FULL VIEW 2170011
against your throat each time you wear your helmet.
GRAPHICS DEVELOPMENT AMENDMENT (PER UNIT/PER AMENDMENT) 2170011
3. CHECKING THE FIT
C
ADDITIONAL CHARGE CHROME 2170035
Correctly position the helmet on your head and stand in front of a mirror.
M ADDITIONAL CHARGE PAINT SPOILER/PEAK 2170038 Gently rotate the helmet first from left to right and then from front to back. If the skin on
Y ADDITIONAL CHARGE PAINT AIR INTAKE/SIDE COVERS 2170039 your brow moves with the helmet as it is rotated, the fit is proper. If the skin on your brow
does not move when the helmet is rotated in either direction, the fit is too loose. Try
CM ADDITIONAL CHARGE CHROME SPOILER/PEAK 2170040
various sizes until you find one that fits correctly. With the helmet properly positioned,
ADDITIONAL CHARGE CHROME AIR INTAKE/SIDE COVERS 2170041
MY and the chin strap fastened, try to remove the helmet from your head. Grasp it securely
ADDITIONAL CHARGE USED HELMET 2170043 and make a serious effort to roll it off your head in both the forward and backward
CY
directions. If you can remove the helmet or are able to roll the helmet backward far
CMY enough to expose your forehead or forward far enough to block your vision, the helmet
either fits too loosely or the straps are not properly adjusted.
K
If the helmet is too large or if you can still remove the helmet, DO NOT use it and replace
with a smaller size.
OTHER SERVICES Repeat steps 1 through 3
If you cannot remove the helmet and it does not roll either backward far enough to
expose your forehead or forward far enough to block your vision, you have a proper fit.
INTERIOR FULL KIT REBUILD SERVICE CHARGE (Complimentary to SKU 218xxxx) 2170006 We recommend fitting the helmet with a head sock or balaclava if you intend to wear one
in competition.
INTERIOR KIT ASSEMBLY CHARGE (After painted shell) 2170050
REPLACEMENT SERVICE BELL HELMET (Hans post anchor-drinking tube-chinstrap-radio kit) 2170084
4. TEST DRIVE
Steps 1 through 3 are critical to getting the most out of your helmet.Spend as much time
as necessary to satisfy yourself that you have a good fit. Only after successfully
completing steps 1 through 3, put on your helmet and wear it for an extended period
or take a test drive. If the helmet feels comfortable, remaining firmly in place and the
straps remained properly adjusted, your helmet is ready to use. If the helmet feels
SIZING CHART uncomfortable or moves excessively, go through steps 1 through 3 as necessary to
correct the problem. If you are unable to successfully complete all 3 steps, or if the
helmet does not fit and feel comfortable, DO NOT continue to use the helmet.
Metric 52 53 54 55 56 57 58 59 60 61 61+ 63 64 65 66 67 68 Either: Return to the dealer for assistance, or contact Bell Racing for further
Size
instructions.
Generic 3XS XXS XSM SML MED LRG XLG 2XLG 3XLG 4XLG Do not use chin cups or wear the strap on the point of the chin.
Size This will increase the risk of the helmet coming off in an accident.
Hat 1 5 3 7 7 1 1 1 3 1 5 3 7 / - 8 1 1 3 1
7
8
8
4
4
8
8
Size 6 /2 - 6 /8 6 / - 6 / 8 7 / - 7 /4 7 / - 7 /8 7 /2 7 / - 7 / 4 8 8 / - 8 /4 8 / - 8 /2
more info at
www.bellracing.com
96 97
SERVICE SERVICE