Page 107 - Catalogo Bell 2024
P. 107

ai1703684047244_BRE 2024 96 97 ok Print.pdf   1   27/12/2023   4:34 PM
 CUSTOM PAINTING
                                                                                     SERVICE

                              1. POSITIONING THE HELMET ON YOUR HEAD
                              Put the helmet on by grasping the chin strap halves in each hand and pull the helmet on over your head.

          HOW TO FIT A HELMET
 FACTORY CUSTOM PAINTING SERVICE


 Bell Racing offers factory custom painting with the guarantee that the painting will not affect the original protective qualities of the helmet.  1. POSITIONING THE HELMET ON YOUR HEAD
 Each painted helmet comes with an official certificate, proving its conformity with the FIA safety regulations.  Put the helmet on by grasping the chin strap halves in each hand and pull the helmet on over your head.
 Our experience over the past years in painting the helmets of F1 and other professional drivers enables us to reproduce almost every possible
 design and colours.
                                                2. FITTING THE HELMET
                                                When properly positioned, the helmet should be worn low on the brow eyes, near the
                                                center of the eye opening, touching the top of the head with uniform and firm pressure
                                                all around – tight without excessive pressure points.
 PAINTING JOB LEVEL 1  2170031
                                                To fasten the chin strap, thread the end of the strap through both d-rings, loop the strap
 PAINTING JOB LEVEL 2  2170032                  end back through the inner d-ring and pull it comfortably tight against the throat. Make
                                                sure the chin strap is snug against the throat.
 PAINTING JOB LEVEL 3  2170033
 PAINTING JOB LEVEL 4  2170034
                                                        WARNING CORRECTLY USING THE CHIN STRAP
 GRAPHICS DEVELOPMENT DESIGN ONE VIEW  2170011  A good fit and a properly fastened chin strap are all that keep the helmet on your head
                                                during an accident. Make sure the chin strap is correctly fastened and pulled snugly up
 GRAPHICS DEVELOPMENT DESIGN FULL VIEW  2170011
                                                against your throat each time you wear your helmet.
 GRAPHICS DEVELOPMENT AMENDMENT (PER UNIT/PER AMENDMENT)  2170011
                                                3. CHECKING THE FIT
 C
 ADDITIONAL CHARGE CHROME  2170035
                                                Correctly position the helmet on your head and stand in front of a mirror.
 M  ADDITIONAL CHARGE PAINT SPOILER/PEAK  2170038  Gently rotate the helmet first from left to right and then from front to back. If the skin on
 Y  ADDITIONAL CHARGE PAINT AIR INTAKE/SIDE COVERS  2170039  your brow moves with the helmet as it is rotated, the fit is proper. If the skin on your brow
                                                does not move when the helmet is rotated in either direction, the fit is too loose. Try
 CM  ADDITIONAL CHARGE CHROME SPOILER/PEAK  2170040
                                                various sizes until you find one that fits correctly. With the helmet properly positioned,
 ADDITIONAL CHARGE CHROME AIR INTAKE/SIDE COVERS  2170041
 MY                                             and the chin strap fastened, try to remove the helmet from your head. Grasp it securely
 ADDITIONAL CHARGE USED HELMET  2170043         and make a serious effort to roll it off your head in both the forward and backward
 CY
                                                directions. If you can remove the helmet or are able to roll the helmet backward far
 CMY                                            enough to expose your forehead or forward far enough to block your vision, the helmet
                                                either fits too loosely or the straps are not properly adjusted.
 K
                                                If the helmet is too large or if you can still remove the helmet, DO NOT use it and replace
                                                with a smaller size.
 OTHER SERVICES                                 Repeat steps 1 through 3
                                                If you cannot remove the helmet and it does not roll either backward far enough to
                                                expose your forehead or forward far enough to block your vision, you have a proper fit.
 INTERIOR FULL KIT REBUILD SERVICE CHARGE (Complimentary to SKU 218xxxx)  2170006  We recommend fitting the helmet with a head sock or balaclava if you intend to wear one
                                                in competition.
 INTERIOR KIT ASSEMBLY CHARGE (After painted shell)  2170050
 REPLACEMENT SERVICE BELL HELMET (Hans post anchor-drinking tube-chinstrap-radio kit)   2170084
                                                4. TEST DRIVE
                                                Steps 1 through 3 are critical to getting the most out of your helmet.Spend as much time
                                                as necessary to satisfy yourself that you have a good fit. Only after successfully
                                                completing steps 1 through 3, put on your helmet and wear it for an extended period
                                                or take a test drive. If the helmet feels comfortable, remaining firmly in place and the
                                                straps remained properly adjusted, your helmet is ready to use. If the helmet feels
 SIZING CHART                                   uncomfortable or moves excessively, go through steps 1 through 3 as necessary to
                                                correct the problem. If you are unable to successfully complete all 3 steps, or if the
                                                helmet does not fit and feel comfortable, DO NOT continue to use the helmet.
 Metric  52  53  54  55  56  57  58 59  60  61  61+ 63  64  65  66  67  68  Either: Return to the dealer for assistance, or contact Bell Racing for further
 Size
                                                instructions.
 Generic  3XS  XXS  XSM  SML  MED  LRG  XLG  2XLG  3XLG  4XLG  Do not use chin cups or wear the strap on the point of the chin.
 Size                                           This will increase the risk of the helmet coming off in an accident.

 Hat  1  5  3  7  7  1  1  1  3  1  5  3  7  / - 8    1  1  3  1
 7
 8
 8
 4
 4
 8
 8
 Size  6  /2 - 6  /8  6  / - 6  / 8  7  / - 7  /4 7  / - 7  /8  7  /2  7  / - 7  / 4  8  8  / - 8  /4  8  / - 8  /2
                                                      more info at
                                                    www.bellracing.com
 96                                                                                                97
 SERVICE                                                                                                    SERVICE
   102   103   104   105   106   107   108   109   110   111   112